Texture Paints

Premium Plus® Texture Paint

Premium Plus® Texture Paint

Get superior durability through this easy to apply texture paint ideal for hiding imperfections. Reinforced with interwoven fibers for added strength when used on primed or low-sheen surfaces.

Tech Data Sheet HERE

Available In

  • Premium Plus® Texture Paint Ceiling "Popcorn" Finish No. 559 - MSDS
  • Premium Plus® Texture Paint Sand Finish No. 1002 - MSDS
  • Premium Plus® Texture Paint Smooth Finish No. 1001 - MSDS

Where to Use

  • Primed or low-sheen surfaces. Smooth and Sand Finishes ideal for walls and ceilings in Living Rooms, Dining Rooms, Bedrooms, Hallways and Kitchens. Popcorn Finish is ideal for ceilings in Living Rooms, Dining Rooms, Bedrooms, Hallways and Kitchens.
  • Preparation†

  • Remove loose paint, wash off any dirt and grease with detergent, remove mildew stains with a mildrew stain removing product.
  • Scuff sand glossy surfaces.
  • Countersink nailheads, repair imperfections and sand smooth.
  • Remove all dust with a damp cloth and allow to dry.
  • Allow new stucco, plaster and masonry to cure for 30 days before priming.
  • Prime

  • Use a product such as BEHR ENAMEL UNDERCOATER PRIMER & SEALER NO. 75. On new drywall in low-moisture rooms, use a product such as BEHR NEW DRYWALL PRIMER & SEALER NO. 73
  •  

    Application

  • Use product when the surface and air temperatures are between 50-90°F (10-32°C).
  • Stir thoroughly prior to use. Coverage is 100-200 sq. ft. (9-18 m2) per 2 gallon container depending on application technique and surface condition.
  • Initial Application:
  • Apply product to a 4' x 4' section using a looped roller. Continue to work in 4' x 4' sections until the entire surface is complete. Allow to dry at least 4 hours. If necessary, apply a  second coat using the same process. Note: additional coats will increase textured effect.
  • Designer Texture Effect:
  • Apply product to a 4’ x 4’ section using a looped roller and allow to set 5 minutes. Follow the specific technique instructions in the BEHR PREMIUM PLUS® Texture Paint guide.   Continue to work in 4’ x 4’ sections and overlap slightly into the existing section until the entire surface is complete. Allow to dry at least 4 hours.
  • Once the texture fi nish has dried 24-48 hours, to change color and increase durability, apply BEHR PRIMER NO. 75 and topcoat with BEHR PREMIUM PLUS paint. Refer to paint label for further instruction.
  •  

    Dry Time

  • Dries in 4 hours at 75°F (23°C) and 50% humidity. Longer dry time required in cooler temperatures and in higher humidity.
  • Surface will fully cure in 1 week.
  • Clean Up & Storage

  • Use soap and water.
  • Properly dispose of all soiled rags and protect unused product from freezing.
  • For disposal of unused paint products, please contact your household refuse collection service.
  •  

    Important!

    IMPORTANT! DO NOT OPEN CONTAINER WITHOUT READING THESE INSTRUCTIONS.

    Warning

    † WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

    Behr Paints and Stains offers you their Solid Color Concrete Stain to protect and enhance both interior and exterior concrete surfaces. The paint can be used on vertical and horizontal surfaces and forms a strong, long-lasting film. Product safety information is readily available from BehrPro.com.