Solid Color Deck, Fence & Siding Stain - BehrPro

Solid Color Waterproofing Wood Stain

This solid color stain provides protection from water and the sun’s harmful rays for up to 5 years on decks and 15 years on fences and siding. Available in over 1,600 custom colors and formulated for color matching, this stain will hide imperfections while allowing the wood texture to show through. The 100% acrylic formula resists cracking, peeling and blistering. This product is also great for composite decks.

Tech Data Sheet HERE

Accent Base No. 216 - MSDS

Tintable Bases

Deep Base No. 213 - MSDS

Pre-mixed Colors Available in Select Markets

Ultra Pure White® No. 210 - MSDS

WHERE TO USE

Recommended for properly prepared new to heavily weathered or cracking wood surfaces (0 to 15+ years exposure) such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences, Wood Patio Furniture and Composites.

PREPARATION†

(The following steps and products are recommended for best results.)

Use a product such as BEHR premium ™ NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
BEHR PREMIUM NO. 63 All-In-One Wood Cleaner MUST be used following NO. 64 to clean, brighten & neutralize wood.
When NO. 64 is not needed, use a product such as NO. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus. Rinse thoroughly and allow to dry before coating.
On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood. Lightly sand to remove remaining wood fibers/fuzz.

APPLICATION

Must apply between 40-90˚F (4.5-32˚C). Do not use if rain is expected within 24 hours. The wood surface must be completely dry before application.

No primer needed on most woods. However, Redwood, Cedar, Cypress and other "bleeding" woods contain water soluble extractives which may cause discoloration of white and pastel colors; therefore prime the above type woods with one coat of a product such as BEHR PREMIUM PLUS® NO. 436 Exterior Multi-Surface Primer & Sealer. See label for additional instructions.

Intermix multiple containers to ensure color uniformity. Stir product occasionally throughout application.

Use a 3/8” nap roller, nylon/polyester brush, pad applicator or airless sprayer. Airless spray is recommended for experienced applicators only; use a .015 - .019" tip.

If thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.

Maintain a wet edge when applying. Always back-brush and apply product end to end or to board lengths to prevent lap marks.

Over application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily. For optimum performance, coat all six sides of wood.

DRY TIME

1-2 hours before recoat. Wait 24-48 hours before light foot traffic. 72 hours for full cure.

DISPOSAL

For disposal of empty containers and unused product, contact your household refuse collection service.

†WARNING!

If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.

A quality product that contains a mildewcide will assist in providing a finish that is resistant to mildew, provided that all existing mildew is removed prior to application. While this product does contain a mildewcide, it will not prevent mildew growth.